| AFUE Rating | : | 95 % |
| Additional Information | : | No Evaporator Coil Cabinet, R410A and A2L(454B) Indoor Coil Compatible |
| Amperage Rating | : | 8.4 A |
| Cabinet Dimensions | : | 24.6 in L x 19.9 in W x 56 in H |
| Configuration | : | Front Return Downflow |
| Connection Size | : | 1/2 in |
| Connection Type | : | NPT |
| Finish | : | Aluminized |
| Frequency Rating | : | 60 Hz |
| Fuse Rating | : | 20 A |
| Input BTU Rating | : | 72000 Btu/hr |
| Material | : | Stainless Steel/Steel |
| Motor Type | : | ECM |
| Mounting Type | : | Surface |
| Number of Stages | : | 1 |
| Phase | : | 1 ph |
| Pressure Rating | : | 0.3 in-WC |
| Series | : | MG2R Series |
| Temperature Rise | : | 35 to 65 deg F |
| Transformer Rating | : | 40 VA |
| Vent, Ducted or Ductless | : | Vent |
| Voltage Rating | : | 115 V |
The high efficiency downflow gas furnace is designed for all manufactured housing applications. It may be installed in a utility room, or enclosed in a closet. CSA design certified for use in the United States and Canada.
Intertherm® Condensing Gas Furnace, MG2R Series, Input BTU Rating: 72000 Btu/hr, 115 V, 8.4 A, 95 % AFUE Rating, 1 ph Phase, 60 Hz, 1 Stages, Front Return Downflow, NPT Connection Type, 1/2 in Connection, 24.6 in L x 19.9 in W x 56 in H Cabinet, ECM Motor, Vent, Ducted or Ductless: Vent, 20 A Fuse Rating, 40 VA Transformer, 0.3 in-WC, Surface Mounting, Stainless Steel/Steel, Aluminized, 35 to 65 deg F Temperature Rise, Additional Information: No Evaporator Coil Cabinet, R410A and A2L(454B) Indoor Coil Compatible
- 100% fired and tested - All units and each component (both mechanical and electrical) are tested on the manufacturing line.
- Clean and quiet operation - Due to the unique design of in-shot burners, location of inducer and use of insulation.
- Fixed 30 second blower delay - At burner start-up assures a warm outlet air temperature at furnace start-up. Adjustable blower off settings (60, 90, 120 and 180 seconds).
- Fixed 30-second post purge - Increases life of heat exchanger.
- Dependable, hot surface ignitor - Innovative application of silicon nitride type igniter. Utilizes proven Smartlite® technology to extend igniter life.
- Tubular primary heat exchanger - Heavy gauge aluminized steel heat exchanger assures a long life.
- Stainless steel secondary heat exchanger - Assures a long life.
- 60 second fixed cooling cycle blower-off delay (TDR) - Increases cooling performance when matched with a Nordyne coil.
- Sealed combustion approved for direct vent furnace, category IV venting system - May be vertically or horizontally vented using a two-pipe system for maximum flexibility in installation.
- LP convertible - Simple burner orifice (included w/unit)and gas valve regulator change for ease of convertibility.
- 3 amp fuse protection against low voltage shorts - Protects transformer and control board.
- Low voltage terminal board - For easy field wiring.
- Easy open pawl latch - Secures the door firmly for transit, yet allows easy removal for access.
- Appliance quality door - Protects against rust and other corrosion. Baked enamel finish allows for easy cleaning.
- Color coded wire harness - Designed to fit the components, all with quick-connect fittings for ease of service and replacement.
- Multi-speed ECM blower - Designed to give a wide range of cooling capacities. Switches on PCB, provide ultra easy motor speed selection. 40VA transformer included.
- Diagnostic lights for easy troubleshooting without counting flashes - Dedicated light for flame signal strength and 2 lights in combination to indicate all other fault codes with easy to recognize states without counting flashes.